Weed Eater BC2400 Instruction Manual download pdf (Page 4)

4

operate in a locale where such regulations ex-

ist, you are legally responsible for maintaining

the operating condition of these parts. Failure

to do so is a violation of the law. For normal

homeowner use, the muffler and spark arrest-

ing screen will not require any service. After

50 hours of use, we recommend that your

muffler be serviced or replaced by your autho-

rized service dealer.

ASSEMBLY

CARTON CONTENTS

Check carton contents against the following

list:

S

Brushcutter

S

Handlebar screws (2)

S

Blade shield screws (4)

S

Cupped washer

S

Large nut for installing blade

S

Long hex wrench

S

Short hex wrench

S

Bracket cover

S

Metal shield

S

Plastic shield

S

Shoulder strap with warning

S

4--point weed blade

S

Trimmer head (assembled on unit)

S

Handlebar

S

Wing nut (screwed onto shield)

S

Container of oil

WARNING:

Always stop unit and dis-

connect spark plug before performing any as-

sembly procedures.

WARNING:

If received assembled,

repeat all steps to ensure your unit is properly

assembled and all fasteners are secure.

Examine parts for damage. Do not use dam-

aged parts.

NOTE:

If you need assistance or find parts

missing or damaged, call 1-800-554-6723.

It is normal for the fuel filter to rattle in the

empty fuel tank.

Finding fuel or oil residue on muffler is normal

due to carburetor adjustments and testing

done by the manufacturer.

TOOLS REQUIRED

S

2 hex wrenches (provided)

S

Adjustable wrench or large pliers

S

Phillips screwdriver

ATTACHING THE HANDLEBAR

DANGER:

During blade usage, the

barrier portion of the handlebar must be

installed as shown to provide a barrier be-

tween operator and the spinning blade.

1. Locate the decal on the handlebar. This

decal includes two arrows. Position the

handlebar with the mounting bracket be-

tween these arrows.

2. Position the bracket cover over the han-

dlebar. Again make sure the handlebar is

between the arrows.

3. Insert screws and hand tighten only. Be

sure the handlebar is installed correctly;

then, tighten each screw securely with

the short hex wrench.

Bracket Cover

Screw

Mounting

Bracket

Handlebar

ASSEMBLY OF SHOULDER STRAP

WARNING:

Proper shoulder strap

and handlebar adjustments are required before

starting the engine.

1. Try on shoulder strap and adjust for fit and

balance before starting the engine or begin-

ning a cutting operation.

2. Insert your right arm and head through.

the shoulder strap and allow it to rest on

your left shoulder. Make sure the danger

sign is on your back and the hook is to the

right side of your waist.

NOTE:

A one-half twist is built in the shoulder

strap to allow the strap to rest flat on the shoul-

der.

3. Adjust the strap, allowing the hook to be

about 6 inches below the waist.

4. Fasten the strap hook to the clamp located

between the trigger handle and the handle-

bar clamp base and lift the tool to the oper-

ating position.

CONFIGURING YOUR UNIT

You can configure your unit using a cutting

head for grass and light weeds, or a weed

blade for cutting grass, weeds, and brush up

to 1/2 inch in diameter. To assemble your unit,

go to the section for the desired configuration

and follow the instructions.

ASSEMBLY INFORMATION --

TRIMMER HEAD

TRIMMER

HEAD

NOTE:

Remove the blade and metal shield

before attaching the plastic shield and trimmer

head. Refer to the sections ASSEMBLY IN-

FORMATION -- WEED BLADE and reverse the

steps to remove the metal shield and blade.

1 2 3 4 5 6 7 8 9 ... 14 15

Comments to this Manuals

No comments